调压阀规范归纳
——| 规范序号 | 规范中文名字 | 规范英语名 |
| GB/T13852-1992 | 船舶液压控制阀技术性标准 | General specification of hydraulic control valves for ship |
| GB/T17490-1998 | 液压控制阀油孔、底版、操纵设备和电磁线圈的标志 | Hydraulic fluid power--Identification of valve ports,subplates,control devices and solenoids |
| GB/T15623.1-2003 | 液压传动系统 电调配液压控制阀 第1一部分：四通方位流量控制阀实验方式 | Hydraulic fluid power-Electrically modulated hydraulic control valves-Part 1:Test methods for four-way directional flow control valves |
| GB/T15623.2-2003 | 液压传动系统 电调配液压控制阀 第2一部分：三通方位流量控制阀实验方式 | Hydraulic fluid power-Electrically modulated hydraulic control valves-Part 2:Test methods for three-way directional flow control valves |
| GB/T17213.7-1998 | 工业生产流程调压阀第7一部分: 调压阀数据信息单 | Industrial-process control valves Part 7: Control valve data sheet |
| GB/T17213.8-1998 | 工业生产流程调压阀第8一部分: 噪音的考虑到第1节: 试验室内精确测量空气动力流流径调压阀造成的噪音 | Industrial-process control valves Part 8: Noise considerations Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves |
| GB/T17213.1-1998 | 工业生产流程调压阀第1一部分: 调压阀专业术语和条例 | Industrial--Process control valves Part 1: Control valve terminology and general considerations |
| GB/T17213.5-1998 | 工业生产流程调压阀第5一部分: 标示 | Industrial-process control valves Part 5: Marking |
| GB/T2514-1993 | 四油孔平板式液压机方位调压阀组装面 | Hydraulic fluid power--Four-port directional control valves--Mounting surfaces |
| GB/T8104-1987 | 流量控制阀实验方式 | Hydraulic fluid power--Valves--Testing method of flow control valves |
| GB/T7940.3-2001 | 气动式五气口方位调压阀第三一部分: 作用鉴别编号管理体系 | Pneumatic fluid power--Five-port directional control valves--Part 3: Code system for communication of valve functions |
| GB/T8106-1987 | 方位调压阀实验方式 | Hydraulic fluid power--Valves--Testing method of directional control valves |
| GB/T7940.2-2001 | 气动式五气口方位调压阀第二一部分通电气接头的组装面 | Pneumatic fluid power--Five-port directional control valves--Part 2: Mounting interface surfaces with optional elettrical connector |
| GB/T8105-1987 | 压力控制阀实验方式 | Hydraulic fluid power--Valves--Testing method of pressure control valves |
| GB/T7940.1-2001 | 气动式五气口方位调压阀第一部分: 不通电气接头的组装面 | Pneumatic fluid power--Five-port directional control valves--Part 1: Mounting interface surfaces without electrical connector |
| GB/T8100-1987 | 平板式连接液压机压力控制阀(不包括调速阀)顺序阀、卸压阀、单向节流阀和节流阀组装面 | Hydraulic fluid power--Pressure control valves (excluding pressure relief valves ), sequence valves, unloading valves, throttle valves and check valves--Mounting surfaces |
| GB/T8098-2003 | 液压传动系统带赔偿的流量控制阀组装面 | Hydraulic fluid power--Compensated flow control valves--Mounting surfaces |
| JB/T7387-1994(2005复核) | 工业生产过程控制系统用电动式调压阀 | |
| NF C46-520-1993 | 工业生产流程调压阀.第8一部分:噪音问题.第2节:根据调压阀的液压机流动性造成的噪音的试验室精确测量 | (Industrial-process control valves. Part 8 : noise considerations. Section 2 : laboratory measurement of noise generated by hydrodynamic flow through control valves.) |
| NF C46-522-1994 | 工业生产解决调压阀.第8一部分:噪音条文.第4节:液压机流动性造成的噪音预订(EN 534-8-4) | (Industrial-process control valves. Part 8 : noise considerations. Section 4 : prediction of noise generated by hydrodynamic flow.) |
| NF E49-080-1-2002 | 标准气压液控阀.五通定项调压阀.第1一部分:没有射频连接器的组装插口 | (Pneumatic fluid power - Five-port directional control valves - Part 1 : mounting interfaces without electrical connector.) |
| NF E49-080-2-2002 | 标准气压液控阀.五通方位调压阀.第2一部分:随意选择电气设备射频连接器的组装插口面 | (Pneumatic fluid power - Five-port directional control valves - Part 2 : mounting interface surfaces with optional electrical connector.) |
| NF C46-505-1998 | 绝缘层全过程调压阀.第2-3一部分:总流量容积.实验全过程 | (Industrial-process control valves. Part 2-3 : flow capacity. Test procedures.) |
| NF C46-630-1998 | 工业生产流程调压阀.第6一部分:调压阀与定位仪联接用组装关键点.第1节:线形传动系统上安装使用的定位仪 | (Industrial-process control valves. Part 6 : mounting details for attachment of positioners to control valves. Section 1 : positioner mounting on linear actuators.) |
| NF E29-453-2000 | 工业生产过程控制闸阀 | (Industrial process control valves.) |
| NF E29-316-5-2001 | 供电用闸阀.适用范围规定和专用型查验实验.第5一部分:操纵闸阀 | (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5 : control valves.) |
| NF C46-521-2001 | 工业生产流程调压阀.第8一部分:噪音问题.第3节:气动控制阀噪声预测分析法 | (Industrial-process control valves - Part 8-3 : noise considerations - Control valves aerodynamic noise prediction method.) |
| NF E48-435-1998 | 液压传动系统.规格02、03和05的四端口号方式自动排气阀和四端口号方位调压阀.夹持规格 | (Hydraulic fluid power. Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05. Clamping dimensions.) |
| NF C46-519-2001 | 工业生产流程调压阀.第8一部分:噪音考虑到.第1节:试验室精确测量气动式流过调节阀造成的噪音 | (Industrial-process control valves - Part 8 : noise considerations - Section 1 : laboratory measurement of noise generated by aerodynamic flow through control valves.) |
| NF C46-531-2001 | 工业生产流程调压阀.第6-2一部分:定位仪装到调压阀的组装实施方案.转动传动系统上安装使用的定位仪 | (Industrial-process control valves - Part 6-2 : mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators.) |
| NF E49-091-2002 | 气压传动.调压阀和其他构件的管口和操纵机械设备的认证 | (Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components.) |
| XP E29-140-1999 | 应用化石燃料的家庭用设备的调压阀.安全性调压阀(含有集中化全自动密闭式器的) | (Control cocks for household appliances using gaseous fuels - Safety cocks (with integrated automatic obturator).) |
| NF C46-510-2001 | 工业生产流程调压阀.第3-1一部分:规格.双通球形自动式操纵法兰阀门的零距离规格和双通球形视角操纵法兰阀门的核心 | (Industrial-process control valves - Part 3-1 : dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, a) |
| NF C46-511-2001 | 工业生产流程调压阀.第3-2一部分:规格.碟阀以外的转动操纵阀体的零距离规格 | (Industrial-process control valves - Part 3-2 : dimensions - Face-to-face dimensions for rotary control valves except butterfly valves.) |
| NF E49-090-2-2003 | 气压传动.18mm和26mm五气口方位调压阀.第2一部分:带电子光学电连接头的组装面 | (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2 : mounting interfaces with optional electrical connector.) |
| NF C46-512-1999 | 工业生产解决调压阀.第3-3一部分:规格.对电焊的首尾相连规格.两连接头球形立即式调压阀(欧洲标准EN 60534-3-3) | (Industrial-process control valves. Part 3-3 : dimensions. End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves.) |
| ANSI/IEEE 1290-1996 | 核发电厂电动式调节闸阀电机运用、安全防护、操纵和实验手册 | (Guide for MOV (Motor-Operated Valve) Motor Application, Protection, Control, and Testing in Nuclear Power Generating Stations) |
| ANSI/FCI 87-2-1990 | 扭簧模版推动调压阀驱动力数据信号规范 | (Power Signal Standard for Spring-Diaphragm Actuated Control Valves) |
| ANSI/ISA 75.08.02-2003 | 无凸台的调压阀内孔间的规格(等级150、300和600) | (Face-to-Face Dimensions for Flangeless Control Valves (Classes 150, 300, and 600) ) |
| ANSI/ISA S 75.08.03-2001 | 承插电焊焊接端部和螺旋式端部球形调压阀的面到面规格 | (Face-to-Face Dimensions for Socket Weld-End and Screwed-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500)) |
| ANSI/ISA 75.08.06-2002 | 带凸台的球形操纵油路板的零距离规格(种类900、1500和2500) | (Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900, 1500, and 2500) ) |
| ANSI/ISA 75.08.05-2002 | 端部对接焊球形调压阀的零距离规格(种类150、300、600、900、1500和2500) | (Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (Classes 150, 300, 600, 900, 1500, and 2500) ) |
| ANSI/ISA 75.01.01-2002 | 规格调压阀用总流量表达式 | (Flow Equations for Sizing Control Valves ) |
| ANSI/ISA 75.08.01-2002 | 集成式带凸台的球形操纵油路板的零距离规格(种类125、150、250、300和600) | (Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (Classes 125, 150, 250, 300, and 600) ) |
| ANSI/ISA S 75.19.01-2001 | 调压阀的自流水实验 | (Hydrostatic Testing of Control Valves) |
| ANSI/ISA S 75.08.04-2001 | 对接焊端部球形调压阀的面到面规格 | (Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves) |
| ANSI/ISA S 75.08.07-2001 | 单独法兰盘球形调压阀的面到面规格 | (Face-to-Face Dimensions for Separable Flanged Globe-Style Control Valves (Classes 150, 300, and 600)) |
| ANSI/(NFPA) T 3.5.14 R1-1997 | 液压传动.立即操纵闸阀.交界特点的测定法 | (Hydraulic Fluid Power - Directional Control Valve - Method for Determining the Metering Characteristics) |
| ANSI/(NFPA) T 3.21.8-1990 | 标准气压液控阀.反应速度的精确测量.立即操纵闸阀 | (Pneumatic Fluid Power - Measurement of Response Time - Directional Control Valves) |
| ANSI/ISA S 75.15-1993 | 对接焊端球形调压阀的零距离规格(ANSI级别150、300、600、900、1500、2500) | (Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500)) |
| ANSI/FCI 91-1-1997 | 操纵闸阀密封性的检测标准 | (Standard for Qualification of Control Valve Stem Seals) |
| ANSI/UL 753-1996 | 消防安全设备用全自动供电调压阀的报警配件 | (Alarm Accessories for Automatic Water-Supply Control Valves for Fire-Protection Service) |
| BS EN 60534-2-5-2003 | 工业生产流程调压阀.商品流通工作能力.根据有段间恢复功能的两段调压阀的介质总流量的校正公式计算 | (Industrial-process control valves - Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery) |
| ASTM F 1985-1999 | 力气实际操作的球型调压阀技术标准 | (Standard Specification for Pneumatic-Operated, Globe-Syle, Control Valves) |
| BS EN 60534-3-2-2001 | 工业生产流程调压阀.规格.碟形阀以外的转式调压阀的内孔距 | (Industrial-process control valves - Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves) |
| BS ISO 15407-2-2003 | 气压传动.五气口方位调压阀,规格型号18mm和26mm.有随意选择电连接头的组装插口 | (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Mounting interface surfaces with optional electrical connector) |
| BS ISO 12238-2001 | 标准气压液控阀.方位操纵闸阀.变换时长的精确测量 | (Pneumatic fluid power - Directional control valves - Measurement of shifting time) |
| BS ISO 5599-1-2001 | 标准气压液控阀.五通方位调压阀.没有射频连接器的组装插口表层 | (Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces without electrical connector) |
| BS ISO 5599-2-2001 | 标准气压液控阀.五通方位调压阀.随意选择电气设备射频连接器的组装插口面 | (Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces with optional electrical connector) |
| BS EN 60534-6-2-2001 | 工业生产流程调压阀.定位仪装到调压阀的组装实施方案.转动传动系统上安装使用的定位仪 | (Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators) |
| BS EN 1074-5-2001 | 供电闸阀.适用范围和专用型规定的实验.操纵闸阀 | (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Control valves) |
| BS EN 60534-8-3-2000 | 工业生产步骤调压阀.噪音问题.调压阀的空气动力噪音气象预报法 | (Industrial-process control valves - Noise considerations - Control valve aerodynamic noise prediction method) |
| BS EN 60534-2-3-1998 | 工业生产流程调压阀.总流量.实验程序流程 | (Industrial-process control valves - Flow capacity - Test procedures) |
| BS EN 60534-8-1-2001 | 工业生产流程调压阀.噪音问题.根据调压阀的驱动力噪音的试验室精确测量 | (Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves) |
| BS EN 60534-3-1-2000 | 工业生产流程调压阀.规格.带法兰盘的双路、球形、自动式操纵阀体的零距离规格和带法兰盘的双路、球形、视角操纵闸阀 | (Industrial-process control valves - Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle patter) |
| BS EN 1349-2000 | 工业生产解决操纵闸阀 | (Industrial process control valves) |
| BS ISO 15407-1-2000 | 18mm和26mm五气一口气动方位调压阀.无电插头的组装页面 | (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Mounting interface surfaces without electrical connector) |
| BS ISO 11727-1999 | 气动式流体动力学.调压阀和其他元器件的操纵机械设备设备和气缸的鉴别 | (Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components) |
| BS EN 60534-3-3-1998 | 工业生产流程调压阀.规格.连接电焊焊接,两向,球形,竖直方式调压阀的终端对尾端规格 | (Industrial-process control valves - Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves) |
| BS EN 60534-2-1-1999 | 工业生产流程调压阀 .流容.组装标准下流液经营规模方程式 | (Industrial-process control valves - Flow capacity - Flow capacity - Sizing equations for fluid flow under installed conditions) |
| BS ISO 6263-1997 | 液压传动系统.赔偿式流量控制阀.安装面 | (Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces) |
| BS ISO 10770-2-1998 | 液压传动系统.电方式液压控制阀.第2一部分:三向流动性调压阀的检验方式 | (Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for three-way directional flow control valves) |
| BS ISO 10770-1-1998 | 液压传动系统.电方式液压控制阀.第1一部分:四向流动性调压阀的检验方式 | (Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for four-way directional flow control valves) |
| BS EN 60534-6-1-1998 | 工业生产流程调压阀 .控制阀控制器联接用组装元器件.平行线传动系统上控制器的组装 | (Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators) |
| BS ISO 7790-1998 | 液压传动系统.规格型号为03和05型的四油口设计标准叠阀和四油孔定项调压阀.拧紧规格 | (Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions) |
| EN 60534-8-1-2000 | 工业生产流程调压阀 第8一部分：噪音的考虑到 第1节：气动式流流径调压阀造成的噪音的试验室精确测量 | Industrial-process control valves - Part 8: Noise consideration; Section 1: Laboratory measurement of noise generated by hydrodynamic aerodynamic flow through control valves (IEC 60534-8-1:1986) |
| EN 60534-8-4-1994 | 工业生产流程调压阀 第8一部分：噪音问题 第4节：流动性造成的噪音的预测分析 | Industrial-process control valves - Part 8: Noise considerations - Section 4: Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:1994) |
| EN 60534-8-3-2000 | 工业生产步骤调压阀 .第8-3一部分 噪音问题 根据调压阀的驱动力噪音预测分析法 | Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method (IEC 60534-8-3:2000) |
| EN 1074-5-2001 | 供电闸阀 目地规定的适应能力和适宜的验证实验 第5一部分：操纵闸阀 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves |
| EN 60534-3-1-2000 | 工业生产流程调压阀 第３－１一部分：规格 法兰盘双通球型直型调压阀的内孔间隔规格和有法兰盘双通球形角型调压阀的 | Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves (IEC 60534-3-1:2000) |
| EN 60534-2-1-1998 | 工业生产流程调压阀 第2－1一部分：商品流通工作能力 组装标准下液体总流量的校正公式计算 | Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions (IEC 60534-2-1:1998) |
| EN 60534-1-1993 | 工业生产流程调压阀 第1一部分 调压阀专业术语和一般考虑到 | Industrial-process control valves - Part 1: Control valve terminology and general considerations (IEC 60534-1:1987) |
| EN 60534-3-2-2001 | 工业生产流程调压阀 第３一部分：规格 第２节：没法兰调压阀（薄形碟阀以外）的内孔间隔规格 | Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534-3-2:2001) |
| EN 60534-3-3-1998 | 工业生产流程调压阀 第三一部分：规格 连接电焊焊接 两向 球形 竖直方式调压阀的终端对尾端规格 | Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves (IEC 60534-3-3:1998) |
| EN 60534-6-1-1997 | 工业生产流程调压阀 第6－1一部分：定位仪联到调压阀执行器的组装实施方案 第1节：平行线传动系统上控制器的组装 | Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators (IEC 60534-6-1:1997) |
| EN 60534-6-2-2001 | 工业生产流程调压阀 第6－2一部分：定位仪联到调压阀执行器的组装实施方案 环状执行器定位仪 | Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators (IEC 60534-6-2:2000) |
| EN 60534-8-2-1993 | 工业生产流程调压阀 第8一部分 噪音考虑到 第2节根据调压阀的液体形成的噪音的试验室精确测量报法 | Industrial-process control valves- Part 8: noise consideration- Section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:1991) |
| EN 60534-2-3-1998 | 工业生产流程调压阀 第２一部分：商品流通工作能力 第３节：实验技术规范 | Industrial-process control valves - Part 2-3: Flow capacity - Test procedures (IEC 60534-2-3:1997) |
| prEN 13959-2000 | 磅级在DN6至DN250（含DN250）的污染治理调压阀 E族A、B、C和D型 | Anti-pollution check valves DN 6 to DN 250 inclusive - Family E, type A, B, C and D |
| prEN 60534-4-1998 | 工业生产流程调压阀 第４一部分：检测和基本实验 议案 | IEC 60534-4: Industrial-process control valves - Part 4: Inspection and routine testing |
| EN 1349-2000 AC-2001 | 工业生产生产加工操纵闸阀 | Industrial process control valves |
| EN 60534-2-5-2003 | 工业生产生产加工调压阀 第2-5一部分：总流量 根据带级间修复多级别调压阀的液体规格方程式 | Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery (IEC 60534-2-5:2003) / Note: Endorsement notice |
| BS ISO 4401-1996 | 液压传动系统.四油孔定项调压阀.安装面 | (Hydraulic fluid power - Four-port directional control valves - Mounting surfaces) |
| BS EN 60534-1-1989 | 工业生产流程调压阀 .第1一部分:调压阀专业术语和一般考虑到 | (Industrial-process control valves - Industrial-process control valves - Control valve terminology and general considerations) |
| BS EN 60534-8-4-1994 | 工业生产流程调压阀.第8一部分:噪音问题.第4节.流动性造成的噪音的气象预报 | (Industrial-process control valves - Noise considerations - Prediction of noise generated by hydrodynamic flow) |
| BS EN 60534-8-2-1991 | 工业生产流程调压阀.第8一部分:噪音考虑到.第2节:根据调压阀的液体形成的噪音的试验室精确测量 | (Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves) |
| BS 6494-4-1989 | 液压阀门的组装面.第4一部分:03和05规格型号的四孔部件自动排气阀、模二维数组阀和方位调压阀夹持规格标准 | (Hydraulic fluid power valve mounting surfaces - Specification for clamping dimensions of four-part, size 03 and 05, modular stack valves and directional control valves) |
| BS 5793-4-1987 | 工业生产流程调压阀.第4一部分:检测和常规实验标准 | (Industrial-process control valves - Specification for inspection and routine testing) |
| BS 5944-4-1984 | 液压系统软件和构件所形成的气体噪声的精确测量.第4一部分:总流量和压力控制阀声功率级的测定法 | (Measurement of airborne noise from hydraulic fluid power systems and components - Method of determining sound power levels from valves controlling flow and pressure) |
| BS 5793-5-1984 | 工业生产流程调压阀.第5一部分:标识标准 | (Industrial-process control valves - Specification for marking) |
| BS 1655-1950 | 过程控制工业级法兰连接全自动调压阀(面至面规格)标准 | (Specification for flanged automatic control valves for the process control industry (face-to-face dimensions)) |
| DIN EN 60534-2-3-1998 | 工业生产流程调压阀.第2-3一部分:总流量.检测方式 | (Industrial-process control valves - Part 2-3: Flow capacity; test procedures (IEC 60534-2-3:1997); German version EN 60534-2-3:1998) |
| DIN EN 60534-6-1-1998 | 工业生产步骤调压阀.第6一部分:调节阀推动的部位控制器固定不动用组装关键点.第1节:行程安排推动上部位控制器的组装 | (Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Postioner mounting on linear actuators (IEC 60534-6-1:1997); German version EN 60534-6-1:1997) |
| DIN EN 60534-1-1995 | 工业生产流程调压阀.第1一部分:调压阀专业术语和一般基本原理 | (Industrial-process control valves - Part 1: Control valve terminology and general considerations (IEC 60534-1:1987); German version EN 60534-1:1993) |
| DIN IEC 60534-7-1992 | 工业生产流程调压阀.第7一部分:.数据分析表 | (Industrial process control valves; control valve data sheet; identical with IEC 60534-7:1989) |
| DIN IEC 60534-2-4-1990 | 工业生产流程调压阀.第2一部分:商品流通工作能力.第4节:本质的移动特点线和调整占比关联 | (Industrial-process control valves; flow capacity; inherent flow characteristics and rangeability; identical with IEC 60534-2-4:1989) |
| DIN EN 60534-8-2-1994 | 工业生产流程调压阀.第8一部分:噪音问题.第2节:由根据调压阀的液力传动流形成的噪音的试验室精确测量 | (Industrial-process control valves; part 8: noise considerations; section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:1991); German version EN 60534-8-2:1993) |
| DIN EN 60534-8-4-1995 | 工业生产流程调压阀.第8一部分:噪音情况.第4节.流动性造成的噪音的气象预报 | (Industrial-process control valves - Part 8: Noise considerations; section 4: Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:1994); German version EN 60534-8-4:1994) |
| DIN EN 60534-3-1-2000 | 工业生产流程调压阀.第3-1一部分:规格.双通球形自动式操纵法兰阀门的零距离规格和双通球形视角操纵法兰阀门的核心 | (Industrial-process control valves - Part 3-1: Dimensions; Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves (IEC 60534-3-1:2000); German version EN 60534-3-1:2000 Corrigendum 2000) |
| DIN 3394-3-2004 | 全自动调压阀.第3一部分:工作压力为4巴及下列的0级缓解压力阀门 | (Automatic control valves - Part 3: Class 0 pressure relief, valves for pressure up to 4 bar) |
| DIN EN 60534-3-3-2000 | 工业生产流程调压阀.第3-3一部分:规格.死对头电焊焊接的死对头规格,二种方法,球形,斜角型操纵闸阀 | (Industrial-process control valves - Part 3-3: Dimensions - end-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves (IEC 60534-3-3:1998); German version EN 60534-3-3:1998) |
| DIN EN 60534-2-1-2000 | 工业生产流程调压阀.第2-1一部分:流动性容积.在组装标准下液体流动性的规格方程式 | (Industrial-process control valves - Part 2-1: Flow capacity; sizing equations for fluid flow under installed conditions (IEC 60534-2-1:1998); German version EN 60534-2-1:1998) |
| DIN EN 1074-5-2001 | 供电闸阀.适用范围规定和兼容实验.第5一部分:操纵闸阀 | (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves; German version EN 1074-5:2001) |
| DIN EN 12334-2001 | 阀门产品.生铁操纵闸阀 | (Industrial valves - Cast iron check valves; German version EN 12334:2001) |
| DIN EN 60534-8-3-2001 | 工业生产流程调压阀.第8-3一部分:噪音问题.调压阀空气动力噪音预测分析法 | (Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method (IEC 60534-8-3:2000); German version EN 60534-8-3:2000) |
| DIN IEC 60534-5-1984 | 工业生产流程调压阀.第5一部分:标识 | (Industrial-process control valves; part 5: marking) |
| DIN EN 60534-6-2-2001 | 工业生产流程调压阀.第6-2一部分:定位仪装到调压阀上的组装实施方案.转动传动系统上安装使用的定位仪 | (Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators (IEC 60534-6-2:2000); German version EN 60534-6-2:2001) |
| DIN EN 1349-2000 | 工业生产过程控制闸阀 | (Industrial process control valves; German version EN 1349:2000) |
| DIN EN 60534-8-1-2001 | 工业生产流程调压阀.第8一部分:噪音问题.第1节:由根据调压阀的空气动力流形成的噪音的试验室精确测量 | (Industrial-process control valves - Part 8: Noise considerations; Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves (IEC 60534-8-1:1986); German version EN 60534-8-1:2000) |
| DIN ISO 15407-1-2003 | 气压传动.五气口方位调压阀、规格型号18mm和26mm.第1一部分:无电气设备连接头的组装面 | (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 1: Mounting interface surfaces without electrical connector (ISO 15407-1:2000)) |
| DIN ISO 5599-1-1998 | 标准气压液控阀.五通方位调压阀.第1一部分:不通电联接件的组装插口表层 | (Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connectors (ISO 5599-1:1989)) |
| DIN EN 60534-3-2-2002 | 工业生产流程调压阀.第3-2一部分:规格.没法兰调压阀(薄形碟阀以外)的内孔间隔规格(IEC60534-3-2:2001) | (Industrial-process control valves - Part 3-2: Dimensions; Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534-3-2:2001); German version EN 60534-3-2:2001) |
| IEC 60534-3-2-2001 | 工业生产流程调压阀.第3-2一部分:规格.碟形阀以外的转式调压阀的内孔距 | (Industrial-process control valves - Part 3-2: Dimensions; Face-to-face dimensions for rotary control valves except butterfly valves) |
| IEC 60534-2-5-2003 | 工业生产全过程控制阀.第2-5一部分:商品流通工作能力.根据有段间恢复力的两段操纵阀体的介质总流量的校正公式计算 | (Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery) |
| IEC 60534-5-1982 | 工业生产流程调压阀.第5一部分:标示 | (Industrial-process control valves. Part 5 : Marking) |
| IEC 60534-2-1-1998 | 工业生产流程调压阀.第2-1一部分:总流量.组装标准下液体总流量的校正公式计算 | (Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions) |
| IEC 60534-8-4-1994 | 工业生产流程调压阀.第8一部分:噪音情况.第4节.流动性造成的噪音的气象预报 | (Industrial-process control valves - Part 8: Noise considerations - Section 4: Prediction of noise generated by hydrodynamic flow) |
| JIS B8656-2002 | 占比电动式液压机旁通阀流量控制阀实验方式 | (Test methods for electro-hydraulic proportional bypass flow control valves) |
| JIS B8654-2002 | 占比电动式液压机串连型流量控制阀实验方式 | (Test methods for electro-hydraulic proportional series flow control valves) |
| JIS B8657-2002 | 占比电动式液压机定项旁通阀流量控制阀实验方式 | (Test methods for electro-hydraulic proportional directional bypass flow control valves) |
| JIS B8659-2-2002 | 液压传动系统.电气设备调整液压控制阀门.第2一部分:三路定项流量控制阀门的检验方式 | (Hydraulic fluid power -- Electrically modulated hydraulic control valves -- Part 2: Test methods for three-way directional flow control valves) |
| UL 429-1999 | 电动式调压阀 | (Electrically operated valves ) |
| UL 753-1995 | 消防安全设备用全自动供电调压阀警报配件 | (Alarm accessories for automatic water-supply control valves for fire protection service ) |
| UL 1468-1995 | 消防设备用立即操纵的调压阀和压力控制阀 | (Direct acting pressure reducing and pressure restricting valves ) |
| UL 1739-1994 | 安防设备用液压系统操纵的压力控制阀 | (Pilot-operated pressure-control valves for fire-protection service ) |
| JIS B8655-2002 | 占比电动式液压机串连型定项流量控制阀实验方式 | (Test methods for electro-hydraulic proportional directional series flow control valves) |
| JIS B8375-3-2000 | 气动液压.五孔定项调压阀.第3一部分:阀作用通信的登陆密码系统软件 | (Pneumatic fluid power -- Five-port directional control valves -- Part 3: Code system for communication of valve functions) |
| JIS B8375-1-2000 | 气动液压.五孔定项调压阀.第1一部分:没电连接头的组装页面 | (Pneumatic fluid power -- Five-port directional control valves -- Part 1: Mounting interface surface without electrical connector) |
| JIS B8357-2000 | 液压传动系统., , , 赔偿式流量控制阀.安装面 | (Hydraulic fluid power -- Compensated flow-control valves -- Mounting surfaces) |
| JIS B8400-1-2003 | 气压传动.规格为18mm-26mm的五孔定项调压阀.第1一部分:没电联接件的组装插口表层 | (Pneumatic fluid power -- Five-port directional control valves, sizes 18 mm and 26 mm -- Part 1: Mounting interface surfaces without electrical connector) |
| JIS F3024-1996 | 造船业.调压阀用舱面橡胶支座 | (Shipbuilding -- Deck stands for controlling valves) |
| JIS B8658-1989 | 占比电动式液压控制阀用电力工程放大仪标准 | (Rules of electronic amplifier for electro-hydraulic control valves) |
| JIS B8380-2002 | 标准气压液控阀.操纵闸阀和别的元构件出入口和操纵组织的评定 | (Pneumatic fluid power -- Identification of ports and control mechanisms of control valves and other components) |
| JIS B8376-1994 | 气动式速率调压阀 | (Speed control valves for pneumatic use) |
| JIS B8387-2000 | 液压.四孔调节阀和四孔方位操纵闸阀.02,03,05规格.夹紧规格 | (Hydraulic fluid power -- Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 -- Clamping dimensions) |
| JIS B8375-2-2000 | 气动液压.五孔定项调压阀.第2一部分:带预留电连接头的组装页面 | (Pneumatic fluid power -- Five-port directional control valves -- Part 2: Mounting interface surface with optional electrical connector) |
| JIS B8664-2001 | 液压.压力控制阀(不包括调压阀)、次序悬板、释荷阀、单向节流阀和截止阀.组装表层 | (Hydraulic fluid power -- Pressure-control valves (excluding pressure-relief valves), sequence valves, unloading valves, throttle valves and check valves -- Mounting surfaces) |
| JIS B8659-1-2000 | 液压.电气设备调整液压控制阀门.第1一部分:四路直流电操纵阀体的检验方式 | (Hydraulic fluid power -- Electrically modulated hydraulic control valves -- Part 1: Test methods for four-way directional flow control valves) |
| JIS B2007-1993 | 工业生产流程调压阀.检测和基本实验 | (INDUSTRIAL-PROCESS CONTROL VALVES - INSPECTION AND ROUTINE TESTING) |
| ISO 10770-2-1998 | 液压传动系统.电方式液压控制阀.第2一部分:三向流动性调压阀的检验方式 | (Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 2: Test methods for three-way directional flow control valves) |
| ISO 5599-3-1990 | 气压传动.五口调压阀.第3一部分:闸阀作用互换的编号管理体系 | (Pneumatic fluid power; five-port directional control valves; part 3: code system for communication of valve functions) |
| ISO 7790-1997 | 液压传动系统.规格型号为03和05型的四油口设计标准叠阀和四油孔定项调压阀.拧紧规格 | (Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions) |
| ISO 11727-1999 | 气旋驱动力.调压阀和其他元器件的操纵机械设备设备和气缸的鉴别 | (Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components) |
| ISO 5599-2-2001 | 标准气压液控阀.五通方位调压阀.第2一部分:随意选择电气设备射频连接器的组装插口面 | (Pneumatic fluid power - Five-port directional control valves - Part 2: Mounting interface surfaces with optional electrical connector) |
| ISO 15407-1-2000 | 18mm和26mm五气一口气动方位调压阀.第1一部分:无电源插头组装页面 | (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 1: Mounting interface surfaces without electrical connector) |
| ISO 6263-1997 | 液压传动系统.赔偿式流量控制阀.安装面 | (Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces) |
| ISO 4401-1994 | 液压传动系统.四油孔定项调压阀.安装面 | (Hydraulic fluid power - Four-port directional control valves - Mounting surfaces) |
| ISO 15407-2-2003 | 气压传动.五气口方位调压阀,规格型号18mm和26mm.第2一部分:可随意选择射频连接器的组装插口 | (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2: Mounting interface surfaces with optional electrical connector) |
| ISO 5599-1-2001 | 标准气压液控阀.五通定项调压阀.第1一部分:没有射频连接器的组装插口表层 | (Pneumatic fluid power - Five-port directional control valves - Part 1: Mounting interface surfaces without electrical connector) |
| ISO 12238-2001 | 标准气压液控阀.方位操纵闸阀.变换时长的精确测量 | (Pneumatic fluid power - Directional control valves - Measurement of shifting time) |
| ISO 10770-1-1998 | 液压传动系统.电方式液压控制阀.第1一部分:四向流动性调压阀的检验方式 | (Hydraulic fluid power - Electrically modulated hydraulic control valves - Part 1: Test methods for four-way directional flow control valves) |
| IEC 60534-8-3-2000 | 工业生产流程调压阀.第8-3一部分:噪音的考虑到.调压阀的气动式噪音预测分析法 | (Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method) |
| IEC 60534-8-2-1991 | 工业生产流程调压阀.第8一部分:噪音问题.第2节:由根据调压阀的液力传动流形成的噪音的试验室精确测量 | (Industrial-process control valves; part 8: noise considerations; section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves) |
| IEC 60534-2-3-1997 | 工业生产流程调压阀.第2-3一部分:商品流通工作能力.实验技术规范 | (Industrial-process control valves - Part 2-3: Flow capacity - Test procedures) |
| IEC 60534-8-1-1986 | 工业生产流程调压阀.第8一部分:噪音的考虑到.第1节:流过调压阀的气动式流形成的噪音的试验室精确测量 | (Industrial-process control valves. Part 8 : Noise considerations. Section one - Laboratory measurement of noise generated by aerodynamic flow through control walves) |
| IEC 60534-3-3-1998 | 工业生产流程调压阀.第3一部分:规格.对焊的两向阀,球形阀,立即图型调压阀的首尾相连规格 | (Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves) |
| IEC 60534-6-1-1997 | 工业生产流程调压阀.第6一部分:定位仪装到操纵驱动的组装实施方案.第1节:线形致动器上定位仪组装 | (Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators) |
| IEC 60534-3-1-2001 | 工业生产流程调压阀.第3-1一部分:规格.法兰盘零距离规格,双路,直型和法兰盘核心正对面规格,双路,球型,角型操纵闸阀 | (Industrial-process control valves - Part 3-1: Dimensions; Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves) |
| IEC 60534-6-2-2000 | 工业生产流程调压阀.第6-2一部分:定位仪连接到调压阀的组装实施方案.环形执行器定位仪 | (Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators) |
| IEC 60534-3-1976 | 工业生产流程调压阀.第3一部分:规格.第1节:二通球型调压阀的法兰盘内孔距 | (Industrial-process control valves. Part 3 : Dimensions. Section One: Face-to-face dimensions for flanged, two-way, globe-type control valves.) |
| IEC 60534-1-1987 | 工业生产流程调压阀.第1一部分:调压阀专业术语和一般基本原理 | (Industrial-process control valves. Part 1: Control valve terminology and general considerations.) |
| IEC 60534-2-4-1989 | 工业生产流程调压阀.第2一部分:商品流通工作能力.第4节:纯天然流动性特点和测量范围范畴 | (Industrial-process control valves; part 2: flow capacity; section four: inherent flow characteristics and rangeability) |
| IEC 60534-7-1989 | 工业生产流程调压阀.第7一部分:数据分析表 | (Industrial-process control valves; part 7: control valve data sheet) |
| IEC 60534-4-1999 | 工业生产流程调压阀.第4一部分:检测和基本实验 | (Industrial-process control valves - Part 4: Inspection and routine testing) |
| QC/T305-1999(2005复核) | 汽车动力转为调压阀总程技术性标准 |
| QC/T306-1999(2005复核) | 汽车动力转为调压阀总程台架试验方式 | |
| GB/T17213.12-2005 | 工业生产流程调压阀 第3-3一部分：规格 对接焊式两通球型直达调压阀的端距 | |
| GB/T17213.4-2005 | 工业生产流程调压阀 第4一部分：检测和常规实验 | |
| GB/T17213.6-2005 | 工业生产流程调压阀 第6-1一部分：定位仪与调压阀执行器联接的组装关键点 定位仪在直行程安排执行器上的组装 | |
| GB/T17213.13-2005 | 工业生产流程调压阀 第6-2一部分：定位仪与调压阀执行器联接的组装关键点定位仪在角行程安排执行器上的组装 | |
| GB/T17213.14-2005 | 工业生产流程调压阀 第8-2一部分：噪音的考虑到 试验室 内精确测量液动流流过调节阀造成的噪音 | |
| GB/T17213.15-2005 | 工业生产流程调压阀 第8-3一部分：噪音的考虑到 空气动力流流过调节阀造成的噪音预测分析方式 | |
| GB/T17213.16-2005 | 工业生产流程调压阀 第8-4一部分：噪音的考虑到 液动流流过调节阀造成的噪音预测分析方式 | |
| GB/T17213.2-2005 | 工业生产流程调压阀 第2-1一部分：商品流通工作能力 组装标准下液体总流量的计算方法 | |
| GB/T17213.9-2005 | 工业生产流程调压阀 第2-3一部分：商品流通工作能力 实验程序流程 | |
| GB/T17213.10-2005 | 工业生产流程调压阀 第2-4一部分：商品流通工作能力 原有总流量特点和可调式比 | |
| GB/T17213.3-2005 | 工业生产流程调压阀 第3-1一部分：规格 两通球型直达 调压阀法兰盘内孔距和两通球型角型 调压阀法兰盘核心至法兰盘内孔 | |
| GB/T17213.11-2005 | 工业生产流程调压阀 第3-2一部分：规格 角行程安排调压阀(碟阀以外)的内孔距 | |
| MT/T765-1997(2005复核) | 液压支架用全自动喷雾器调压阀通用技术标准 |
上一篇电动蝶阀的运用和检修
下一篇气动阀门的特性与主要用途
咨询需求
